CR-fitwerk
- Alle messingAlles aus MessingAll brass
- KogelkranenKugelhähneBall valves
- Kleppen & beluchtingVentile & BelüftungValves & venting
- Huiddoorvoeren & aardingBorddurchlässe & ErdungSkin fittings & grounding
- Slangpilaren & -verbindersSchlauchtüllen & -verbinderHose tails & connectors
- Bochten & T-stukkenWinkel & T-StückeElbows & tees
- Nippels, sokken & verloopNippel, Muffen & ReduzierstückeNipples, sockets & reducers
- Koppelingen, moeren & doppenKupplungen, Muttern & KappenCouplings, nuts & caps
- GEKAGEKAGEKA
- Alle CR-fitwerkAlle CR-FittingsAll CR fittings
- KogelkranenKugelhähneBall valves
- Huiddoorvoeren & scheproostersBorddurchlässe & AnsaugsiebeSkin fittings & scoop strainers
- SlangpilarenSchlauchtüllenHose tails
- Bochten & T-stukkenWinkel & T-StückeElbows & tees
- Nippels, sokken & verloopNippel, Muffen & ReduzierstückeNipples, sockets & reducers
- Koppelingen, moeren & doppenKupplungen, Muttern & KappenCouplings, nuts & caps
- Alle brons-fitwerkAlle Bronze-FittingsAll bronze fittings
- KogelkranenKugelhähneBall valves
- HuiddoorvoerenBorddurchlässeSkin fittings
- SlangpilarenSchlauchtüllenHose tails
- Bochten & T-stukkenWinkel & T-StückeElbows & tees
- Nippels, sokken & verloopNippel, Muffen & ReduzierstückeNipples, sockets & reducers
- Moeren, doppen & pluggenMuttern, Kappen & StopfenNuts, caps & plugs
- Alle PP-fitwerkAlle PP-FittingsAll PP fittings
- KogelkranenKugelhähneBall valves
- Huiddoorvoeren & tankadaptersBorddurchlässe & TankadapterSkin fittings & tank adapters
- SlangpilarenSchlauchtüllenHose tails
- Bochten, T-stukken & koppelingenWinkel, T-Stücke & VerbinderElbows, tees & connectors
- Nippels & verloopNippel & ReduzierstückeNipples & reducers
- TypeTypType
- Alle montagesnoerenAlle AderleitungenAll single-core wires
- Montagesnoer H07Aderleitung H07Single-core wire H07
- FLRY-B
- Solar kabelSolarkabelSolar cable
- DoorsnedeQuerschnittCross-section
- 0,5 mm²
- 0,75 mm²
- 1 mm²
- 1,5 mm²
- 2 mm²
- 2,5 mm²
- 4 mm²
- 6 mm²
- 10 mm²
- 16 – 120 mm²
- DoorsnedeQuerschnittCross-section
- Alle accukabelsAlle BatteriekabelAll battery cables
- 0,5 – 2,5 mm²
- 4 – 10 mm²
- 16 – 35 mm²
- 50 – 120 mm²
- TypeTypType
- Alle meeraderige kabelsAlle mehradrigen KabelAll multi-core cables
- HalogeenvrijHalogenfreiHalogen-free
- Multi core
- Platte kabelFlachkabelFlat cable
- StuurstroomkabelSteuerleitungControl cable
- WalstroomkabelLandstromkabelShore power cable
- Aantal adersAderzahlCores
- 2-aderig2-adrig2-core
- 3-aderig3-adrig3-core
- 4-aderig4-adrig4-core
- 5-aderig en meer5-adrig und mehr5 cores and more
- Type klemSchellentypClamp type
- Alle klemmenAlle SchellenAll clamps
- WormschroefklemmenSchneckengewindeschellenWorm drive clamps
- Zware klemmen & superstrengthSchwere Schellen & SuperstrengthHeavy duty & superstrength
- MiniklemmenMini-SchellenMini clamps
- LeidingklemmenRohrschellenPipe clamps
- KlembereikKlemmbereichClamp range
- tot 12 mmbis 12 mmup to 12 mm
- 12 – 20 mm
- 20 – 32 mm
- 32 – 50 mm
- 50 – 80 mm
- 80 – 120 mm
- groter dan 120 mmüber 120 mmover 120 mm





CR fittings made of dezincification-resistant brass (CW602N)
CR fittings are fittings made of dezincification-resistant brass, alloy CW602N. They are intended for applications in which ordinary brass can dezincify, such as in seawater. DG Rubber Holland supplies CR ball valves, skin fittings, hose tails, elbows, tees, hex nipples and reducing bushes, from 1/8" up to and including 3". You choose CR fittings by type of fitting, size and thread type.
What are CR fittings?
Ordinary brass is a copper-zinc alloy. In seawater, the zinc can dissolve out of the metal. This is called dezincification and makes the brass porous and weaker. Dezincification-resistant brass (CR) is a brass alloy that is less susceptible to this process. That is why CR fittings are used on board and in other environments where ordinary brass is less suitable. When choosing CR, you otherwise proceed in the same way as with other fittings: type of fitting, size and thread. Another alternative is bronze fittings.
Types of CR fittings
- Ball valves: with female thread on both sides (2x Bi).
- Skin fittings: angled, with strainer and with a 100 mm mushroom head.
- Hose tails: with female or male thread.
- Elbows: 45 and 90 degrees.
- Tees: 3x female thread.
- Hex nipples and reducing bushes: Bi-Bu.
Sizes run from 1/8" up to and including 3" and, for hose connections, from approximately 5 up to and including 120 mm. According to the product specification, the temperature range is between -10 °C and +200 °C. A wrench set for fitting brass and CR skin fittings can be found under other fittings.
Application and combination
CR fittings are used in pipework on board, among other places. For toilet and waste water pipes, combine them with sanitation hoses. Secure the connection with hose clamps in W5 stainless steel. Read more background in the blog differences in fittings.
Frequently asked questions about CR fittings
- What does CR mean for fittings?
- At DG Rubber Holland, CR stands for fittings made of dezincification-resistant brass, alloy CW602N. This is brass that is less susceptible to dezincification than ordinary brass.
- When do I choose CR instead of brass?
- Choose CR in places where ordinary brass can dezincify, such as with seawater. DG Rubber Holland does not recommend ordinary brass for salt water.
- Which skin fittings are available in CR?
- There are angled skin fittings, skin fittings with strainer and skin fittings with a 100 mm mushroom head. For fitting them, a wrench set for brass and CR skin fittings is available.
Not sure which fitting you need? Contact us for technical advice.
Cable calculator
Which cable size do I need?
Enter voltage, current and length and instantly see the right battery cable and cable lugs.
Rubber profiles
From stock or made to measure
Can't find your profile? Then we'll have it made. Through our sister company DG Rubber Profiles we also supply custom profiles, made to your drawing or sample.
Standard profiles at DG Rubber Holland
- Window rubber, sponge rubber, cellular rubber, self-gripping profiles and bumper strips
- Ordered before 14:00, usually delivered the next working day
- Order online straight away at your own prices
Custom work through DG Rubber Profiles
- Profile to your drawing, sample or idea
- Over 4400 dies, own production in the Netherlands
- In TPE, EPDM or silicone, in small and large series
- 1Drawing or sample
- 2Advice and quote
- 3Production and delivery
Need advice for your project?
Contact our technical experts. In urgent cases we will help you as quickly as possible.
